Skip Navigation
Skip to contents
Filter

ARTICLE TYPE

PUBLICATION DATE

15 results
Display

Flapless implant placement with digital 3D imaging and planning system in fully edentulous patient: A case report and 5-year follow-up

Shin MS, Paek J

One of the fastest growing segments of implant dentistry is the utilization of computed tomography (CT) scan data and treatment planning software in conjunction with guided surgery for implant reconstruction...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Use of digital scan data for evaluation of edentulous ridge relationship: A case report for removable prosthesis with unilateral cross bite

Kim JH, Kim JE, Park YB, Lee KW

After the teeth were extracted, maxillary and mandibular alveolar ridges show the opposite resorption pattern and as a result, the mandibular arch is enlarged than maxillary arch relatively. In this...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Fabrication of complete dentures by conventional method and CAD/CAM milling: A case report

Jung Y, Lee J, Hong SJ, Noh K, Kim HS, Pae A

In edentulous patient, not only mastication and pronunciation but also esthetics are compromised. By restoring an edentulous patient with complete dentures, masticatory function and esthetics can be rehabilitated. The advantages...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Full mouth rehabilitation of patient with severe dental caries with implant fixed prosthesis fabricated with milling and 3D printing method: A case report

Kim T, Lee JS, Hong SJ, Kim HS, Kwon KR

Passive fit of prosthesis is an essential property of implant supported prosthesis for long term success and minimization of complications. And the property is determined mostly by fabrication procedure. There...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Full mouth rehabilitation of a patient with severe tooth erosion with a digital crown lengthening guide

Park Y, Hong SJ, Paek J, Pae A, Kim HS

In the oral cavity, the teeth undergo wear and corrosion throughout their lives. Progressive and constant tooth wear is a natural phenomenon of aging, but wear and corrosion due to...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Implant overdenture of mandible with severe unilateral atrophy: Report of two cases

Kim SY, Kwon EY, Jung KH, Jeon HM, Baek YJ, Yun MJ, Huh JB

There are several unfavorable conditions regarding alveolar bone condition that may compromise the denture patient's satisfaction. Chewing efficiency may not be satisfactory when alveolar bone is deficient, and the denture...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
A noninvasive esthetic treatment of isolated microdontia using new high-translucent cubic-phase zirconia (5Y-PSZ) laminate veneers: A case report

Ahn MZ, Ahn DG, Pyo SW, Kim HK

Current trends in restorative dentistry focus on improving the esthetics and keeping the sound dental tissues as long as possible. The aims of this case report were to describe the...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
The use of implant surveyed fixed prosthesis for removable partial denture with a few unilateral remaining teeth: A case report

Park J, Kim JE, Park JM, Kim J, Shim JS

As implant can be covered by National Health Insurance Service (NHIS), it was increased the interest in the removable partial denture (RPD) with the surveyed fixed prosthesis supported by implant...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Implant treatment on anterior cross-bite of a patient who had orthognathic surgery 20 years ago

Park KM, Leesungbok R, Lee SW

Orthognathic surgery of skeletal Class III malocclusion improves oral function and facial appearance. The greater amount of skeletal discrepancy, the greater amount of teeth movement required for decompensation, and this...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Functional impression technique using temporary denture for rehabilitation of severely atrophic maxillary and mandibular ridges

Suh YK, Bae JY, Kim HH

Soft liner is used to functional impression technique when dental stone is immediately poured after taking impression because of viscoelasticity. In this case, a 78-year-old male visited for new dentures....
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Rehabilitation of fully edentulous patient using Ceramill full denture system (FDS)

Lee Y, Kwon KR, Pae A, Noh K, Paek J, Hong SJ

CAD/CAM technology has already been used in most areas of prosthetics. The range of CAD/CAM application in denture fabricating process has been gradually increasing since the CAD/CAM technology was introduced...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Comparison analysis of fracture load and flexural strength of provisional restorative resins fabricated by different methods

Cho WT, Choi JW

PURPOSE: This study was undertaken to compare fracture and flexural strength of provisional restorative resins fabricated by additive manufacturing, subtractive manufacturing, and conventional direct technique. MATERIALS AND METHODS: Five types of...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Time efficiency and operator convenience of using a micro-screw in image registration for guided implant surgery

Mai HY, Lee DH

PURPOSE: The image registration of radiographic image and digital surface data is essential in the computer-guided implant guide system. The purpose of this study was to examine the effects of...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Comparative evaluation of marginal and internal fit of metal copings fabricated by various CAD/CAM methods

Jeong SJ, Cho HW, Jung JH, Kim JM, Kim YL

PURPOSE: The purpose of the present study was to compare the accuracy of four different metal copings fabricated by CAD/CAM technology and to evaluate clinical effectiveness. MATERIALS AND METHODS: Composite resin...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Effect of abutment superimposition process of dental model scanner on final virtual model

Yu BY, Son K, Lee KB

PURPOSE: The purpose of this study was to verify the effect of the abutment superimposition process on the final virtual model in the scanning process of single and 3-units bridge...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close

Go to Top

Copyright © 2021 by Korean Association of Medical Journal Editors. All rights reserved.     E-mail: koreamed@kamje.or.kr