Skip Navigation
Skip to contents
Filter

ARTICLE TYPE

PUBLICATION DATE

10 results
Display

The effet of cooling rate on the residual stresses in the veneer ceramics of zirconia-ceramic restorations: a literature review

Chang JS, Kim S

Nowadays, dental zirconia is widely used as a framework material for a fixed dental prosthesis as well as a single restoration. However, clinical studies have reported high incidence of veneer...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Rehabilitation of maxillary partial edentulous patients using implant assisted removable partial denture

Lee BR, Kim JH

Treatment options for partially edentulous patients are fixed partial denture, removable partial denture and implant supported fixed partial denture. In case of a patient with a few remaining teeth, removable...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Reconstruction of anterior guidance using duplication technique of CAD/CAM: a case report

Bae JC, Kim WH, Jeon YC, Jeong CM, Yoon MJ, Huh JB

Comprehensive prosthetic treatment requires considerations from various points of view. The anterior guidance is important factor in prosthodontic treatment of anterior teeth. Lingual surface contour of anterior restoration is so...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Retentive bond strength of fiber-reinforced composite posts cemented with different surface treatments

Roh H, Noh K, Woo YH, Pae A

PURPOSE: This study will evaluate the effectiveness of various pretreatments when fiber-reinforced composite (FRC) post is bonded to endodontically treated tooth with resin cement. MATERIALS AND METHODS: Canal shaping of FRC...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
The influence of iatrogenic mobilization in the initial stage of implant installation on final osteointegration

Kwak MB, Cho JH, Lee DH, Lee CH

PURPOSE: The aim of present investigation was to find out the influence of several times iatrogenic mobilization in the initial stage of implant installation on bone-implant osteointegration. MATERIALS AND METHODS: The...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Comparative study on the radiopacity of different resin-based implant cements

Han KH, Cheon HY, Kim MS, Shin SW, Lee JY

PURPOSE: This study was aimed to compare the radiopacity of four kinds of currently available resin based implant cements using digital radiography. MATERIALS AND METHODS: Four resin-based implant cements ((Estemp Implant(TM)...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
The effect of heat and press-on-metal technique on marginal fit of metal-ceramic crown

Kim JE, Kim SY, Lee CH

PURPOSE: The purpose of this study is to see what impact the heat and press-on-metal technique has on the marginal fit of metal ceramic crown. MATERIALS AND METHODS: Prior to the...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Rheological properties of dental resin cements during polymerization

Lee JR, Lee JB, Han JS, Kim SH, Yeo IS, Ha SR, Kim HK

PURPOSE: The purpose of this study was to observe the change of viscoelastic properties of dental resin cements during polymerization. MATERIALS AND METHODS: Six commercially available resin cement materials (Clearfil SA...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
In vitro study of microleakage of endodontically treated teeth restored with different adhesive systems and fiber-reinforced posts

Park JH, Choi YS

PURPOSE: While studies have examined microleakage in endodontically treated teeth restored with posts, microleakage among post and adhesive systems remains a concern. This study compared the sealing properties of 3...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close
Comparison of the mechanical properties and microstructures of fractured surface for Co-Cr alloy fabricated by conventional cast, 3-D printing laser-sintered and CAD/CAM milled techniques

Choi YJ, Koak JY, Heo SJ, Kim SK, Ahn JS, Park DS

PURPOSE: The purpose of present study is to compare mechanical properties and microstructural characteristics of fractured surface for cast, 3-D printing laser sintered and CAD/CAM milled cobalt-chromium (Co-Cr) alloy specimens...
CITED
export Copy
Close
SHARE
Twitter Facebook
Close

Go to Top

Copyright © 2021 by Korean Association of Medical Journal Editors. All rights reserved.     E-mail: koreamed@kamje.or.kr